AWI: PCoIP Connection Manager Session Settings¶
Select the PCoIP Connection Manager session connection type from the Configuration > Session page to configure the client to use a PCoIP Connection Manager as the PCoIP session broker or when connecting to a HP Anyware host.
AWI Session connection type – PCoIP Connection Manager
The following parameters can be found on the AWI PCoIP Connection Manager page.
AWI PCoIP Connection Manager Parameters
|Server URI||Enter the Uniform Resource Identifier (URI) for the PCoIP Connection Manager or HP Anyware host when connecting directly to HP Anyware.
The URI must be in the form https://<host FQDN> or https://<ip address>.
|Desktop Name to Select||Enter the desktop name used by the client when starting a session.
This field is case-insensitive.
|Certificate Check Mode||Select the level of verification performed on the certificate presented by the connection server:
|Certificate Check Mode Lockout||When enabled, prevents users from changing the Certificate Check Mode settings from the OSD.|
|Auto Connect||This field determines the client’s auto connect behavior after startup:
Enabled: The client automatically connects with the connection server after startup and a PCoIP session ends, bypassing the OSD Connect page.
Disabled: The client does not automatically connect with the connection server.
Enabled With Retry On Error: The client will continuously attempt to contact the connection server. After a connection failure, the client waits before attempting to connect again. This wait time increases with each successive failure. The wait interval is not configurable.
Devices running firmware 4.1.1 or lower do not support Retry On Error behavior and will always perform a single attempt to contact the connection server when this option is selected.
After enabling Auto Connect, the client must be power-cycled for the change to take effect.
|Connection Server Cache Mode||This field determines whether a connection server is dynamically added to the Server drop-down menu on the OSD Connect page when a user types in a valid server URI, or whether it appears in a read-only list for the user to select.
|Enable Self Help Link||See Enabling the Self Help Link for details.|
|Auto Launch If Only One Desktop||When enabled, users are automatically connected to a provisioned desktop after user credentials are entered.
This feature only applies to users who are entitled to a single desktop. It does not apply to users entitled to multiple virtual desktops.
|Remember Username||When enabled, the user name text box automatically populates with the last username entered.|
|Use OSD Logo for Login Banner||When enabled, the OSD logo banner appears at the top of login screens in place of the default banner.|
|Enable Peer Loss Overlay||When enabled, the 'Network Connection Lost' overlay appears on the display(s) when a loss of network connectivity is detected. Normal hypervisor scheduling delays can falsely trigger this message.|
|Enable Preparing Desktop Overlay||When enabled, the 'Preparing Desktop' overlay appears on the display(s) when users log in.
This overlay provides assurance that login is proceeding if the desktop takes more than a few seconds to appear.
|Enable Session Disconnect Hotkey||When enabled, users can press the Ctrl+Alt+F12 hotkey sequence to quickly disconnect a PCoIP session. See Disconnecting from a Session for details.|
|PCoIP Utility Bar Mode||When enabled, the PCoIP Utility Bar appears at the top of the primary display when a user is in session and moves the cursor directly under the bar. The utility bar can be used to disconnect a session or to shut down a remote workstation. For Direct to Host session connection types, Local Cursor and Keyboard must be enabled in order for the Tera2 PCoIP Zero Client to process mouse events for the utility bar. For all connection types, the mouse must be locally connected (that is, not bridged).
|Session Negotiation Cipher Suites||Configure the Transport Layer Security (TLS) cipher to use for negotiating the TLS session between the PCoIP client and the PCoIP host.
|Disconnect Message Filter||This field lets you control what type of messages appear when a session is disconnected. There are three categories:
Information: User- or administrator-initiated actions affecting the session:
You can choose to display:
|Enable DSCP||When enabled, the PCoIP endpoint assigns a Differentiated Services Code Point (DSCP) value determined by the transport session priority negotiation between PCoIP endpoints using proprietary algorithms, enabling intermediate network nodes to prioritize PCoIP traffic accordingly. Additional settings can be configured via group policy for systems using PCoIP software endpoints such as HP Anyware. See your agent documentation for more information.
Sessions between Zero Clients and Remote Workstation Cards will only negotiate a medium priority.
Remote Workstation Card (medium)
Software Agent (configurable OS policy to set session priority to low, medium, or high)
Warning: We don't recommend enabling DSCP on Zero Clients. The purpose of enabling this setting is to reduce the workload on network edge devices of assigning DSCP values on PCoIP packets. Using this setting requires networking expertise and control over the whole link between PCoIP endpoints. See your network administrator and network device documentation for further information on using DSCP in your network.
|Enable Congestion Notification||When enabled, transport congestion notification is enabled to enable PCoIP endpoints to react accordingly if an intermediate network node sets the congestion notification bit in either the IP header or PCoIP transport header. For more information about the PCoIP transport header, see PCoIP Packet Format.|
|Organization ID||Enter an organization ID for the company (for example, 'mycompany.com'). This field accepts any UTF-8 character.
You only need to specify this parameter if the PCoIP Connection Manager requests it. The organization ID is used for certain types of PCoIP Broker Protocol authentication messages.
Enabling the Self Help Link¶
The Self Help Link option lets you configure a self-help link that will appear on the OSD Connect window. When users click this link, they are automatically connected to a specific desktop that can be used as a corporate resource—for example, a desktop containing IT help information. After enabling this option, you configure all the necessary details to automatically log users in to the desktop that you specify. You also configure the link text that you want to appear on the Connect window.
Enable Self Help Link options
When you enable this field, the following options appear:
|Connection Server||Enter the fully-qualified domain name of the connection server brokering the desktop (for example, a PCoIP Connection Manager for a PCoIP Connection Manager session connection type, or a View Connection Server for a View Connection Server session connection type).|
|Port||By default, port 443 is used to communicate with the connection server. If your network is set up to use a non-standard port for secure connections, enter the port number.|
|Username||To password protect the self-help desktop, enter a username in this field.|
|Password||To password protect the self-help desktop, enter a password in this field.|
|Domain||Enter the domain name for the self-help desktop (for example, mycompany.com).|
|Pool Name to Select||Enter the pool or desktop name for the self-help desktop.|
|Link Text||Enter the text that you want to appear as hyperlinked text on the Connect window.|